Oklahoma Metal Building Insulation for Steel Shops and Warehouses

A steel shop near Lawton can be hardest to work in when the afternoon sun heats the roof and west wall. A warehouse near Tulsa may see droplets on the underside of its roof when moist indoor air reaches cold steel. In the Panhandle, a shop heated through winter also needs a plan for heat loss through the roof, walls and overhead doors.

Start with what you notice inside the building. Record where the problem occurs, when it appears and whether the shop is heated, cooled or open to outdoor air for much of the day. Those details will help you decide which surfaces to insulate and what the finished assembly needs to do.

Cool in the Summer. Warm in the Winter. Dry all the Time.

Prodex Total = Insulation + Radiant Barrier + Vapor Barrier — All in One Product.

Start With the Problem You Want to Solve


Afternoon Heat Beneath the Roof


If the building feels hottest beneath the roof late in the day, start by assessing the roof and any west-facing walls. Sun-heated steel can radiate heat toward the work area. Prodex Total’s reflective foil can reduce radiant heat transfer where it faces an appropriate adjacent airspace. Plan that airspace before choosing how to fasten the insulation.


Condensation on Cold Steel

Condensation can form when moist air reaches steel that is cold enough for water droplets to form. Wet vehicles, washdown and other indoor moisture sources can raise humidity. Check the roof for leaks and note when the water appears. A drip at a fastener during rain calls for a different repair from widespread droplets on the underside of cold panels.


A continuous Prodex Total layer with properly sealed seams, edges and penetrations can help limit air and vapor movement toward the steel. Include indoor humidity management in the plan, especially where equipment comes in wet or the building is used for washing.


Winter Heat Loss in a Working Shop


For a shop heated regularly, consider the roof, walls and overhead doors together. Check door seals and wall-to-roof transitions before pricing the work. If the project has a thermal performance target, compare complete assemblies that meet it. Fiberglass and Prodex Total can work together when the design calls for more thermal resistance and a separate layer for radiant heat and vapor control.


Choose an Installation Method for Your Steel Framing


New Construction


If the roof panels are still off, plan the insulation with the installer before the steel goes on. One method runs Prodex Total perpendicular to and over the purlins, with the insulation spanning the framing and the specified airspace beneath the roof panels. Plan seam locations, fastening and edge details at the eaves and around roof penetrations before ordering rolls.


Existing Metal Buildings


Identify the framing before choosing fasteners. On compatible tubular steel framing, Prodex Total can run across the room-facing side of the frame and attach with suitable screws and locking washers. This keeps coverage continuous across the framing, with space behind the insulation.


For I-beams or C- or Z-purlins, adhesive-mounted metal pins and locking caps may suit the assembly. Follow the specified surface preparation and pin spacing, and let the adhesive fully cure before loading the insulation. The national guide on how to insulate a metal building shows the attachment methods and airspace details for both new construction and retrofits.


Compare Metal Building Insulation Options


Prodex Total and Fiberglass


Fiberglass provides thermal resistance when installed at the thickness and in the configuration specified for the assembly. Prodex Total can complement it with added R, radiant heat and vapor control. Keep the intended airspace open at the reflective face, and account for any existing facings or vapor-control layers before adding another layer. Compare material R-values with other material ratings and compare assembly ratings under equivalent conditions, including airspaces and heat-flow direction.


Review Prodex Total vs. fiberglass for metal buildings, or see the Oklahoma fiberglass vs. Prodex Total guide for more on using the two together.


Prodex Total and Spray Foam


Spray foam can conform to irregular surfaces. Its thermal and vapor-control performance depends on the type, thickness and installation. Compare installed quotes for the same roof and wall coverage, including preparation, lift access, labor and any protective finish the assembly requires. See the Prodex Total vs. spray foam comparison for metal buildings.


Select a Roll and Estimate How Much You Need


10M Prodex Total Plus is the most popular and thickest reflective roll in the Prodex Total range. It has a 10 mm (0.4-inch) closed-cell polyethylene foam core faced with reflective foil on both sides. Each 4-foot × 85.3-foot roll covers 341 square feet before cuts and overlaps. Its heat-seal edges let installers heat-weld adjoining rolls.


Measure the roof along its slope, the walls to the eaves and the gable ends separately. Use the Advanced Insulation Calculator for a roll estimate, then check it against your planned roll direction, seams and cuts. Explore the best metal building insulation options for your project before ordering.


If your project is a post-frame shop, see the Oklahoma pole barn insulation guide. For a project focused on the roof or ceiling, see the Oklahoma roof and ceiling insulation guide. Find all applications in the Oklahoma insulation guide.



The regional examples reflect the Oklahoma Climatological Survey’s east–west humidity and temperature patterns. The attachment methods and 10M Plus specifications follow Insulation4Less’s installation guide and product page. Oklahoma Climatological Survey






Need help choosing a product?
circle

Shopping Cart

We use cookies

We use necessary cookies to make our site work and optional cookies to improve your experience. See our Privacy Policy.